Directed Electronics 3200HS Manuel d'instructions

321-56840-21KNov. 2008 ELECTRONIC BALANCE BL SERIES BL320S(L), BL620S(L), BL3200S(L), BL220H(L), BL320H(L), BL2200H(L), BL3200H(L) INSTRUCTION

- VII - Appendix 1 Product Name : Electronic Balance Model No.

CONTENTS 1. COMPONENTS AND THEIR NAMES... 1 2. INSTALLATION...

-1- 1. COMPONENTS AND THEIR NAMES Components Included with every balance are one of the following items. • Balance body • AC adapter (optio

-2- Display and keypad Display Keypad

-3- 2. INSTALLATION Check power voltage • Use only the AC adapter that supplys the output of 12VDC or the AC adapter provided by the distributor

-4- (3) Place the pan supporter on the pan shaft and then the pan on the pan supporter. (4) Plug the AC adapter into the outle

-5- 4. CAUTION NOTES Do not... • put water, metal pin or any thing in the balance; • open the balance case; • leave anything exceeding t

-6- 6. MENU SELECTION This balance is designed to permit selection of the measuring conditions to compensate for vibration and other conditions p

-7- • If the measurement is done at severe measurement environment and the stability of the display is not so good, set the bala

-8- 6.1 Menu selection when “ ” is selected Pressing the TARE key when the “ ” is displayed at 1st hierarchy menu en

-9- (→) : Press the TARE key. (←) : Press the POWER/BRK key. (↓) : Press the CAL/MENU key. • When set to , satisfactory

-10- 6.2 Menu display when is selected Pressing the TARE key when the “ ” is displayed at 1st hierarchy menu enters 2nd

-11- 7. SENSITIVITY CALIBRATION The electronic balance measures mass by electronicity compensating for terrestrial gravitation. Since gravitation

-12- (8) After the setting of weight value is completed, press the TARE key. (9) “ ” is displayed for several seconds and the balan

-13- 7.2 Sensitivity Calibration Perform the sensitivity calibration as follows. Step (1) Warm up the balance well. Refer to “3. WARM-UP”. (2)

-14- 8. REGISTRATION, CANCEL, AND CHANGE OF UNIT Step for registration (1) Press the CAL/MENU key and select the display. (Press th

-15- 9. % SETTING This balance serves percent (%) display by setting the reference sample to 100%. Step (1) Register the % unit. (Refer to “8. Reg

-16- 10. PCS (No. of pieces) SETTING This balance can perform No. of pieces measurement (unit PCS). No. of standard pieces is 10 pcs, 20 pcs, 5

-17- 11. PERFORMANCE CHECKS Conduct performance checks in a room where the temperature does not change suddenly. These checks are used to determ

ELECTRONIC BALANCE BL SERIES BL320S(L), BL620S(L), BL3200S(L), BL220H(L), BL320H(L), BL2200H(L), BL3200H(L) INSTRUCTION MANUAL

-18- Eccentric error Prepare a sample which weights (1) approximately 1/4 of the balance capacity and move it on the pan in the order as s

-19- 13. TROUBLESHOOTING For countermeasures having an asterisk, contact the nearest Shimadzu sales or service center. When What trouble Cause -

-20- 14. SPECIFICATIONS Model BL320S (L) BL620S (L) BL3200S (L) Weighing capacity 320g .620g 3200g Readability 00.01g 0.01g 00.1g Standard d

-21- 15. PARTS LIST Optional accessories Peripheral devices Parts name Parts No. Remarks Printer EP-60A 321-42008-10 Printer EP-80 321-62675-

-22- 16. PERIPHERAL DEVICES 16.1 The EP-60A Electronic Printer Connection When connecting this balance to the EP-60A, first be sure to pull up

-23- 16.2 The IFB-102A RS-232C Interface The IFB-102A is used when the balance is connected to a personal computer. Connection When connecting

-24- Example of connection The above connection is one of examples. This may be different slightly depending on the personal computer connected

-25- 16.3 Input/output Format means space and DL means delimiter. Input data Command code + DL Refer to “16.5 Command Code”. Output

-26- 16.4 Command Code Described in this section are the command codes which can be used when your BL balance is connected to a computer via the IF

-27- 17. Detailed information on Unit Conversion *Remark No.16～21：It can be selected in special Area only. Cent

- I -Requests• Provide this manual to the next user in the event that the instrument is transferred.• To ensure safe operation, contact your Shimadzu

321-56840-21KNov. 2008OPERATION Of BL series 1/2 MENU SELECTION STEP (1) Press the CAL/MENU key during the weight display. (2) “

OPERATION Of BL series 2/2 PCS SETTING STEP (1) Register the PCS unit following the unit registration. (Refer to the following.) When PCS uni

- II - NoteThis instruction manual uses the following notation conventions to indicateSafety Precautions and additional information. CautionIndicate

- III -To ensure that you use the balance safely and correctly, read the following precautions carefully andobserve them. WARNINGNever disassemble, mo

- IV - CAUTIONAvoid locations where the balance will be exposed to any of the following.This could cause accidents or poor performance.• Air flow from

- V -Action for Environment (WEEE)To all user of Shimadzu equipment in the European Union:Equipment marked with this symbol indicates that it was sold

- VI -Declaration of Conformity Manufacturer’s Name: SHIMADZU CORPORATION Analytical & Measuring Instruments Division