Directed Electronics 4400 Guide d'installation

© 2003 Directed Electronics, Inc. Vista, CA N834001 6-03Model 4400Installation GuideNOTE: This product is intended for installation by a professional

10©2002 Directed Electronics, Inc.H1/5 GREEN (-) door trigger input, zone 3Most vehicles use negative door trigger circuits. Connect the GREEN wire to

©2003 Directed Electronics, Inc.11H1/8 BLACK (-) Chassis Ground ConnectionConnect this wire to a clean, paint-free sheet metal location (driver kick p

Secondary Harness (H2),Wire Connection GuideSecondary Harness (H2) Wiring Diagram_________Secondary Harness Wire DescriptionsH2/1 GRAY/BLACK (-) Diese

indicator and the ECM. (See the following diagram for details.)H2/2 LIGHT GREEN/BLACK (-) Factory Disarm OutputThis wire sends a negative pulse every

14©2002 Directed Electronics, Inc.➤Validity: Output that will send a signal as long as the transmission is received.➤Latched: Output that will send a

©2003 Directed Electronics, Inc.15Heavy Gauge Relay Satellite Wire DescriptionsRED (2) (+)12V Input for RelaysRemove the two 30 amp fuses prior to con

Remote Start Harness (H3),Wire Connection GuideRemote Start Harness (H3) Wiring Diagram__________________Remote Start Harness Wire DescriptionsH3/1 BL

This output provides 200mA as soon as the remote starter is activated. It can be used to power arelay to energize a positive (+) third ignition as sho

Connect this wire to the toggle (override) switch as shown in Figure A. Connect the other wire fromthe toggle switch to the park/neutral switch in the

as a shut-down.Testing the Neutral Safety Switch1. Make sure there is adequate clearance to the front and rear of the vehicle because it may movesligh

Bitwriter™, Code Hopping™, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, LearnRoutine™, Nite-Lite®, Nuisance Prevention® Circuitry, NPC®, Revenger®, S

20©2002 Directed Electronics, Inc.NOTE: For detailed instructions about connecting to the vehicle’s power door lock systems, referto the Door Lock Wir

©2003 Directed Electronics, Inc.21Programmer Interface, 3-Pin PortThe BLACK three-pin port is provided for programming of the unit. When using the 998

22©2002 Directed Electronics, Inc.Mounting the Receiver/AntennaReceiver/antenna position should be discussed with the vehicle owner prior to installat

©2003 Directed Electronics, Inc.23Programming JumpersLight Flash JumperThis jumper is used to determine the light flash output. In the (+) position, t

24©2002 Directed Electronics, Inc.System Features Learn RoutineThe System Features Learn Routine dictates how the unit operates. Due to the number of

©2003 Directed Electronics, Inc.255.PPrrooggrraamm tthhee FFeeaattuurree.. While HOLDING the Valet/Program switch, you cantoggle the feature on and

➤➤No activity for longer than 15 seconds.➤➤Press the Valet/Program switch too many times.System Features MenusItems in bold text have been programmed

Menu #3 - Remote Start FeaturesFeature DescriptionsThe features of the system are described below. Features that have additional settings that can bes

28©2002 Directed Electronics, Inc.1-4 ACTIVE/PASSIVE LOCKING: If passive arming is selected in Feature 1-1, then the system canbe programmed to either

©2003 Directed Electronics, Inc.29Menu #2 - Advanced Features2-1 SIREN OUTPUT CONSTANT/PULSED: The system can be programmed to output pulsesinstead of

©2003 Directed Electronics, Inc.3WWaarrnniinngg!! SSaaffeettyy FFiirrsstt ...44IInnss

system will turn on the dome light for 60 seconds when the ignition is turned off. The optionaldome light supervision feature must be installed as des

©2003 Directed Electronics, Inc.31chirp settings. 3-6 VOLTAGE CHECK HI/LOW: This feature only functions when programmed for voltage sense.Some vehicle

32©2002 Directed Electronics, Inc.3.SSeelleecctt tthhee rreecceeiivveerr CChhaannnneell..Press and release the Valet/program switchthe number of t

©2003 Directed Electronics, Inc.33You can advance from one channel to another by releasing the Valet® /Program button and tappingit to advance channel

and operate Battery Saver Modeand operate Beep/Vibrate Notificationand operate Time/Alarm Displayand operate Parking TimerThe standard configuration

©2003 Directed Electronics, Inc.353. The LED will ligh constant when the tach signal is learned.4. Release the Valet/program switch.NOTE: A dim or pul

36©2003 Directed Electronics, Inc.Multi-Level Security Arming Multi-Level Security arming allows the operator to select which inputs and sensors are

©2003 Directed Electronics, Inc.3724-Hour Timer ModeTo enter 24-hour Timer Mode, press and simultaneously. The remote control will producea melody a

38©2003 Directed Electronics, Inc.Table of ZonesNOTE: The Warn Away® response does not report on the LED.Long-Term Event HistoryThe system stores the

©2003 Directed Electronics, Inc.394. Press and release the Valet/Program switch within 5 seconds. The LED willflash in groups indicating the last two

4©2003 Directed Electronics, Inc.Warning! Safety First➤Due to the complexity of this system, installation of this product must only be performed by an

40©2003 Directed Electronics, Inc.neutral safety switch. (See H3/6 BLACK/WHITE neutral safety switch input in RemoteStart Harness Wire Connection Guid

©2003 Directed Electronics, Inc.41Door input does not respond with the progressive trigger, but with immediate full alarm:➤Does the Status LED indicat

©2003 Directed Electronics, Inc.42Wiring Quick Reference Guide

©2003 Directed Electronics, Inc.5Installation Points to RememberBefore Beginning the Installation➤Please read this entire installation guide before be

6©2003 Directed Electronics, Inc.3. Start and run the vehicle. 4. Probe the wire you suspect of being the tachometer wire with the red probe of the me

©2003 Directed Electronics, Inc.7Primary Harness (H1), Wire ConnectionGuidePrimary Harness (H1) Wiring Diagram____________________________________Prim

8©2002 Directed Electronics, Inc.automation, pager or voice module a 1 Amp diode must be installed to ensure proper operation.Insert the diode as show

©2003 Directed Electronics, Inc.9H1/3 WHITE/BLUE (-) Activation InputA momentary input on this wire will start or stop the motor, just as transmitting